24.8K Followers

Home » Campers » Converting a fire van into a camper | Installing walls, vinyl and windows

Converting a fire van into a camper | Installing walls, vinyl and windows

Hi everybody! In this article we continue with the conversion of our fire van. We don’t sit still, because a lot has happened in the meantime! We placed walls, laid a vinyl floor and built in a window. So we’ve been very busy working lately and therefore let our videos and stories take a little longer than you are used to from us.

Also read: How to: Buy or convert a campervan

We have also been to the RDW and we have booked a campsite for our first weekend away! The last time we told about it raising the roof and the insulating fire brigade bus brumm. The next step in the conversion process is installation! Starting with laying the vinyl on the new floor and installing the walls and windows. We’ll tell you all about it in this article!

Installing walls

We started installing the walls after Brumm had completely insulated the fire brigade bus. As we have said before, it is important that Brumm is as light as possible in connection with the inspection at the RDW and the rate of road tax.

Also read:

  1. Converting a fire van into a camper | The Backpack Choice
  2. Converting a fire van into a camper | Buy a suitable bus
  3. Converting a fire van into a camper | RDW design requirements and job plan
  4. Converting a fire van into a camper | A new floor
  5. Converting a fire van into a camper | Insulating the bus
  6. Converting a fire van into a camper | Raising the roof
  7. Converting a fire van into a camper | Installing walls, vinyl and windows

Flexible material – 6mm poplar plywood wood

That’s why we used 6mm poplar plywood for the walls. This material is not only light, but also thin and flexible. That is important, because Brumm is not completely straight. The walls are slightly curved, so when installing the fire truck it is nice if the walls can bend a bit. It is in any case very important to take this curve into account, because if furniture is placed against the walls, one side of the furniture must also have that curve.

Painting and decorating

After cutting the plates, they get a coat of paint. This is not only where the installation starts, but also the furnishing. Because what color do we want on the walls? We will write a separate article about the interior of Brumm and the choices we made, but we can already tell that the walls have turned cream white.

Pay attention to electricity and power points

When you start installing the walls, it is important to consider where the power points and the lamps should be located. The power wires must be laid before the walls are screwed into the frame. After this you can no longer access it. Also take into account the correct wiring. 3x 1.5mm for 220v transit. 2.5mm for 12v throughput.

Laying vinyl in the fire truck

After the walls have been screwed down, we started laying the floor. This is also a furnishing choice. We soon decided which vinyl (sail) we wanted. This is easy to clean, gives a nice warm look, is relatively light, does not rumble, the work is insulating and is also very easy to screw through when you are going to fix the furniture on top. A whole laundry list of benefits!

We need a good chunk of vinyl.

A herringbone floor!

We opted for a vinyl herringbone pattern and the laying could begin! A meticulous job, because the vinyl has to be neatly cut along the walls and wheel arches. Because it was quite a big piece of vinyl, it didn’t fit completely in the width of the fire truck and we had to bend it a little while cutting. After we had the right size of the sail, the gluing could begin. Caution is also advised here because if the gluing does not go well, bubbles will form in the sail and you want to prevent that.

The final result of the floor

Glue for the vinyl on the floor

To stick the vinyl, we bought a pot of universal floor glue from the brand Perfax and spread it out with a trowel. This process can be seen in the video accompanying this article. Unfortunately we just didn’t have enough glue and because the shops were closed (thanks Corona), we couldn’t get a new pot as quickly. Stress of course, because the floor had to be covered. Fortunately there was still a jar of Bison Waterkit. A small risk, because would this work well? But that actually made it much better! The water sealant is thinner and as a result you will get bumps in your vinyl floor much less quickly. Mind you, it stinks but after a day the smell has gone away. After a few hours of pasting, Brumm the fire truck had a nice floor richer! Together with the walls, Brumm suddenly looked so different. That already promised a lot!

Installing windows in the fire brigade bus

After the vinyl floor it is the turn of the windows. When we bought Brumm the fire truck there were no windows at all (except for the windscreens of course). Because we wanted as much daylight as possible, we decided to add 2 other windows in addition to the previously purchased skylight and to place a door with a window. For example, every wall of the fire truck gets a window. We had the ambitious plan to combine the windows with the shutters. It would be a shame to remove the shutters altogether, as they are so typical of the bus!

Install windows!

Fortunately, Denise’s father had come up with the plan to halve the shutters from the bottom, make a wall above it and put the window in there. Both at the back and on one of the sides of the bus, that was the plan. Of course we had all the confidence in the idea and after we had emptied our piggy bank to buy the windows (how expensive those things are!) we could get started.

From roller shutter to window

We sawed the rails of the roller shutters in half halfway and placed curved rails behind them so that the shutter rolls inwards. At the side it comes out under the kitchen worktop and at the back under the bed. We have placed a wall above the exchange hatches. We used wood for the wall and placed aluminum over it. We sprayed this aluminum silver so that the color is the same as that of the roller shutters.

A precise job to place the windows

Installing the window

We also glued the aluminum to the wood with the same glue that we used to glue the roof. Then we sawed a hole the size of the window and glued insulation material around it to the inside of the bus. The wall is also well insulated. We then attached wood over it again and the window could be placed in it.

Often it all seems so simple when we write it down, but in reality this job was mega exciting and a real challenge. When it all seemed to work in the end, we were very happy and proud with the result. And the light in Brumm is so nice! Soon we will be able to look outside from bed, because a nice prospect isn’t it!

This is how we combine the roller shutter with a window

We promise you won’t have to wait that long for the next article and the new video is also in the works. We will guide you through the installation of the furniture.

See you soon!

Also read:

  1. Converting a fire van into a camper | The Backpack Choice
  2. Converting a fire van into a camper | Buy a suitable bus
  3. Converting a fire van into a camper | RDW design requirements and job plan
  4. Converting a fire van into a camper | A new floor
  5. Converting a fire van into a camper | Insulating the bus
  6. Converting a fire van into a camper | Raising the roof
  7. Converting a fire van into a camper | Installing walls, vinyl and windows
derugzakkies

DeRugzakkies

Wij zijn Merijn en Denise en sinds oktober 2020 zijn wij de trotse eigenaren van Brumm de brandweer bus. Eigenlijk zouden wij in maart 2020 vertrekken op wereldreis. Een lang gekoesterde droom die eindelijk in vervulling zou gaan. Covid 19 gooide al onze plannen in de war en deze droom staat voorlopig dan ook in de koelkast.

Omdat wij toch graag willen kunnen reizen hebben we een ander plan bedacht: De Rugzakkies 2.0! We besloten een oude brandweer bus te kopen en deze om te bouwen tot camper. Een enorm tof project waarin we hulp krijgen van de vader van Denise. Hij is een ware expert als het gaat om het (om)bouwen van auto’s en met zijn drieën besteden we heel wat uren aan de ombouw van de bus.

We maken video’s en schrijven verhalen over Brumm en de ombouw tot camper en delen hierover zoveel mogelijk met jullie. En als Brumm straks klaar is om Europa te verkennen nemen we jullie natúúrlijk ook mee op dit avontuur!

Foutje gezien? Vraag? Opmerking? Laat het ons weten in de reacties!

Geschreven door:

derugzakkies

DeRugzakkies

GEZOCHT

REIS CHECKLIST

✔️ Deze reisverzekering dekt óók oranje gebieden.
✔️ Vergelijk en boek de goedkoopste vliegtickets.
✔️ Bespaar en boek alvast de leukste activiteiten.
✔️ Meerdere hotels? Boek dan met 20% Genius korting.
✔️ Bespaar en reserveer je vliegveld parkeerplaats.
✔️ Roadtrip? Vergelijk en boek een voordelige huurauto.
✔️ Reis voorbereiden? Scoor een praktische reisgids.
✔️ Backpack of koffer nodig? Aanbiedingen hier.
✔️ Kadootje? Ik geef 500 keer 10 euro weg!

Translate »
Copy link